Solid End Mills
TaeguTec

StarMill

Difficult-to-cut material machining
- Unequal spaced cutting edges with a high helix angle means decreased vibration and increased feed rate
- Excellent solution for difficult-to-cut materials such as stainless steel, titanium and inconel
- Variety of corner options (Flat, Chamfer, corner R and Ball type) deliver the opportunity to cover
- most machining applications with outstanding performance


SolidFeed

New high feed solid carbide end mill
- Efficient and reduces cycle time with extremely high feed machining capability
- Lowers cutting forces with unique corner geometry
- Designed for rough machining applications including slotting, shouldering, pocketing and helical ramping
- Maximum feed per tooth 1.0 mm/tooth


AluMill

New concept S/C end mill for highly effective aluminum machining
- Chatter free and lower cutting load credit to unique cutting edge wave, variable helix angle and unequal spacing of cutting edges
- Enables high productivity in high speed end milling of aluminum and non-ferrous materials
- Optimally designed for both rough milling and finish milling


HardMill

High performance solid carbide end mill for high hardness materials
- Best solution for high speed machining on high-hardness materials
- TT5505 : an ultra fine substrate with the latest PVD coating grade for hardness & temperature resistant properties that improve tool life and surface finish
- Extensive range of end mills covering a wide range of applications
- Advanced design for high speed machining on hardened materials
- High precision, accurate end mills (‘R’ accuracy tolerance: ±5μm)

VFIMill

High material removal rates to reduce cycle times!

- Unequal spacing of cutting edges eliminate vibrations even at high feed rates
- Four flute, 38° helix angle with unequal spacing improves material removal rates and extends tool life
- Unique chip flow geometry provides excellent chip evacuation and superior surface finish
- Excellent solution for low power machines with DIN69871 30 – 40, BT30 – 40 and HSK 50-63A adaptations

Program
- CFM 4_ 4 flute chamfer type : 6mm to 25mm diameter
ApexMill

Submicron grade for high toughness with AlTiN, TiAlN
PVD coated end mill

- Suitable for conventional to high speed machining
- Submicron grade for high toughness
- AlTiN, TiAlN PVD coated for high wear resistance
- Wide range of product type by application
Flat type
Program
- HMF 2_: 2 flute miniature series – square end (0.4mm to 1.5mm diameter)
- HES 2_T: 2 flute regular series – square end (1mm to 20mm diameter)
- HES 4_T: 4 flute regular series – square end (2mm to 20mm diameter)
- HES 2_LT: 2 flute long series – square end (3mm to 20mm diameter)
- HES 4_LT: 4 flute long series – square end (3mm to 20mm diameter)
- HES 2_XLT: 2 flute extended length – square end (3mm to 20mm diameter)
- HES 4_XLT: 4 flute extended length – square end (3mm to 20mm diameter)
- HES 2_T-R_: 2 flute series – with corner radius (3mm to 20mm diameter)
- HES 4_T-R_: 4 flute series – with corner radius (3mm to 20mm diameter)
- HES 2_LT-R_: 2 flute long series – with corner radius (3mm to 12mm diameter)
- HES 4_LT-R_: 4 flute long series – with corner radius (4mm to 12mm diameter)
- SEH 6_T: 6 flute series for hardened materials (3mm to 20mm diameter)
- SEH 6_XLT: 6 flute extended length for hardened materials (6mm to 20mm diameter)
Ball nose type
Program
- SMB 2_: 2 flute miniature series – ball nose (0.6mm to 1.5mm diameter)
- SBE 2_S: 2 flute short series – ball nose (2mm to 20mm diameter)
- SBE 2_T: 2 flute regular series – ball nose (1mm to 20mm diameter)
- SBE 4_T: 4 flute regular series – ball nose (4mm to 20mm diameter)
- SBE 2_LT: 2 flute long series – ball nose (2mm to 16mm diameter)
- SBO 2_T: 2 flute through coolant – ball nose (6mm to 16mm diameter)
- BES(S) 2,4_T: 2 and 4 flute series – spherical ball end (3mm to 16mm diameter)
MultiMill

The MultiMill is a two in one tool (roughing + finishing) that facilitates one pass finishing!


- 4 flute high helix design with two serrated and two continuous flutes. This permits running at rough milling parameters with the ability to achieve smooth surface finishes
- All 4 flutes are effective simultaneously. No compromise of feed rates
- Unique design enables efficient machining with good chip evacuation and reduced vibrations – even at high loads – resulting in improved tool life
- The MultiMill replaces two end mills (roughing + finishing) without the need for reducing feed rates which drastically reduces machining time
- Reduces tool change and set-up times
- Reduces inventory costs of stocking extra tools
- The MultiMill is ideally suited for machining all types of steels and gives superior performance
- especially in stainless steels, titanium, inconel and other high temperature alloys
Program
- FSM 4_M: Rough + finish, 4 flutes, 45° helix
DiaMill


For graphite machining
- Diamond coatingProgram
- DMR 2_: Square end-corner radius, 2 flutes, 30° helix
- DER 3_S: Square end- corner radius, 3 flutes, 40° helix
- DER 3_L: Square end-corner radius, 3 flutes, 40° helix
- DMB 2_: Ball nose, 2 flutes, 30° helix
- DEB 2_S: Ball nose, 2 flutes, 30° helix
- DEB 2_L: Ball nose, 2 flutes, 30° helix